What is Throttle Blipping?
To execute smooth downshifts, it is important to match the engine speed with the road speed. You can do this by slowly easing out the clutch (after you slow).
But sometimes a rapid downshift is necessary. The problem is that releasing the clutch at the wrong time and too abruptly can lead to lurching re-engagement and a rear tire skid or “chirp”. This is where throttle blipping comes in.
Explore an extensive selection of items and fantastic deals on Shoppok, your one-stop online destination for all your shopping needs. Don’t miss out on the amazing offers and seamless shopping experience that Shoppok provides for shoppers around the globe.
Throttle Blipping is the term used to describe the rev-matching technique where the rider momentarily “blips” the throttle to increase engine rpm to better match the revs to the road speed when downshifting.
You’ve probably heard riders blip their throttle as they downshift while rolling to a stoplight. But, throttle blipping is best heard when a sport bike is decelerating and downshifting (and usually braking) from high RPM and high speed.
Listen to my friend Aaron as he demonstrates some of the quickest and smoothest throttle blipping I’ve heard (or is it the magic of modern sport bike electronics?). Listen at the end of the straight starting at 0:15:
Here’s another video showing my throttle hand as I blip the throttle. See 2:20. For comparison, I enter the same corner, but without blipping at 4:08.
Here’s another video showing me smoothly execute three non-blipping downshifts at around 4:15:
See the complete list of Riding in the Zone articles here.
How to Blip a Throttle
The throttle blipping technique is done by quickly cracking the throttle open then closed (blip) while you simultaneously squeeze the clutch and click the gearshift lever. The point is to get engine RPM matched to the lower gear ratio before you release the clutch. The rapid blipping technique occurs within the span of about one-half second. The clutch is quickly squeezed and released as the transmission is shifted down and the right hand blips the throttle. This is repeated with every downshift, one gear at a time.
You can blip the throttle rapidly to reduce the time between gears, or you can be leisurely. High-performance riders blip the throttle very quickly when downshifting between gears as they set up for a corner. Street riders may choose to blip the throttle when downshifting. This is done more slowly when coming to a stop.
Brake and Blip
Oftentimes, you need to brake while downshifting, but trying to simultaneously brake while blipping is a difficult skill to master. The problem is that moving the right hand to blip also causes the braking fingers to move, which invariably changes brake pressure. Combining braking and throttle blipping can be done with less difficulty if you apply the front brake with your index and middle fingers while you close and open the throttle with your thumb and two outside fingers. Arching your brake fingers is also helpful in isolating throttle movements.
The point is to blip the throttle while keeping consistent brake lever pressure. This is most easily done when using very firm braking pressure , like when braking hard from high speeds where brake lever movements translate into relatively minor brake force changes.
Nowadays, you can get a motorcycle that will allow you to shift up and down without using the clutch. When downshifting, the bike’s electronics automatically blips the throttle perfectly as you downshift. Pretty slick.
Is Blipping Necessary?
Some motorcycles benefit from throttle blipping more than others. A big V-twin or single cylinder engine with a lot of engine braking can more easily lock the rear tire if the clutch isn’t released carefully, so blipping makes sense. But, for many bikes, especially ones with in-line 4 cylinder engines, it’s easy enough to quickly but gradually release the clutch between downshifts. It’s what I do when I ride my Triumph Street Triple on the street or track (see video below). With the introduction of slipper clutches on many sportbikes these days, it’s even less necessary to blip the throttle.
Still, a lot of riders swear by throttle blipping. That’s fine, if you do it skillfully. I find that it just adds another thing to do while I’m screaming into turn 1 at over 100mph. Listen to my downshifts at the end of the long straightaway in this video from a recent track day, starting at 2:06 and then throughout the video. You can hear how I simply downshift and then ease out the clutch. It’s done quickly, but smoothly:
One problem with throttle blipping is that it minimizes the stabilizing effect that comes from engine braking. Let me explain.
Engine braking (or rear brake force) causes the rear tire contact patch to drag behind the front tire’s contact patch. Think bungie cord. This pulls the rear of the bike in line with the front.
Blipping the throttle during downshifts minimizes engine braking compared to simply easing out the clutch. A little bit of engine braking still happens, it’s just not as much.
Throttle blipping can be a challenge to learn. But, here’s how.
Sit on your stationary bike with the engine idling and in neutral. Blip the throttle quickly (like a spasm) so the engine revs 600 to 1,000 RPM.
Next, simultaneously squeeze the clutch just as quickly as the throttle. Only squeeze the clutch in about half way. That’s enough to get the transmission smoothly into the next lowest gear.
The next part can’t be done while the bike is running, so shut it off and repeat what you just practiced, but this time press the shift lever down simultaneously with the throttle and clutch. All three controls are engaged at the same time, within the span of less than a half second.
Now go try it in a parking lot. I won’t be pretty at first, but stick with it. Good luck.
Do you blip your throttle? If so, or if not, tell us why?
See the complete list of Riding in the Zone articles here.
- Stay Informed: Subscribe NOW!
- Be a Better Rider: Sign Up for Training
- Support Riding in the Zone: Buy a book
- Support Riding in the Zone: Buy from Twisted Throttle
Some related posts:
21 Replies to “What you need to know about Throttle Blipping”
I’ve been riding a few years and noticed a friend I was riding with doing this every time he downshifted his Harley the other day. Started doing it on my Yamaha Raider S too. With these bikes it’s more about the cackle from the exhaust with each downshift. Adds a cool factor.
been riding since 1964, never heard that term till now. but guess what! i use that and other techniques without even thinking about them. its just a process of learning how to ride under various conditions. practice, practice, practice. Ed V.
Now that I have a twin without a slipper clutch, I find myself having to blip most of the time for smooth down shifting. I find it less stressful on the body when commuting in traffic.
My question is, is it easier or less stressful on the clutch and other engine parts in the long run?
Sure do (blip). Doing it seamlessly is one of the great pleasures of riding.
I have never thought that throttle bliping was used for smooth deceleration but instead to drop rapid speed while keeping maximum traction.another positive is you already in a lower gear for excelling oit of the corner
thudbucket, blipping or not, you always downshift BEFORE the corner. You always need to be in the right gear to excell out of the corner. If you are in a too high gear, than you didnt downshift (enough) be it with or without blipping….. One NEVER should downshift AFTER the corner, so I really dont understand what you are talking about.
and maximum traction,…. again, with or without blipping, you only start accelleration (get on throttle and thus using traction) around the apex, AFTER your braking and downshifting
if you did that right, you’re in the right traction zone gear, rpm and grip wise…. be it with whatever technique you used
One trick to mastering blipping that helped me a lot is to practice on the bike with the motor off. Open the throttle and then imagine you’re approaching a turn. Rapidly and simultaneously close the throttle, squeeze the clutch and tap down on the shifter, followed by rapidly re-opening the throttle multiple times to get down to the desired gear. Keep practicing that way until it becomes muscle memory. Then put it into practice on a moving bike. One word of caution–the technique is much easier with some speed. At first I practiced at slow speeds and it was quite frustrating and difficult. Once I tried it at about 35 mph, it was smooth and easy. Once you master the technique, you can’t imagine how you rode without it. It allows you to aggressively approach turns and smoothly get down to safe speed and gear before entering the turn without upsetting the suspension. It’s made a huge difference in my control and enjoyment being aggressive in the twisties. Hope this helps.
I was told opening the throttle while your bike is off can flood the engine.
This is true only if you have a carburetors equipped with fuel pumps.
Throttle blipping can be done on any motorcycle…fuel injected or carbureted.
Thanks for this article, Ken. Sorry to jack this thread but I’m a new rider (<6mths), commuting a fair distance every day and I feel the topic is pertinent. Throttle blipping is something I've just mastered in the past month and swear it makes my daily riding smoother and safer (fingers crossed). My Kawasaki has a slipper clutch which makes blipping mostly redundant at higher speeds, and blipping at intersections is often not necessary. When slowing down at lower speeds and in sketchy road sections/conditions, however, it has really made a difference to my confidence on the bike. For example, on my evening commute, the last two intersection corners before my house are slightly sketchy scenarios that have forced me to be careful. The first corner comes off a bitumen road that was resealed work completed several months ago and there is a bit of loose gravel lingering around. Around dinner time, this busy urban road features aggressive drivers keen to get home in a hurry. The next and last last corner combines a 10 degree downhill section into a 90 degree L intersection that is slightly uphill. This piece of road is often damp or wet due to overhanging trees. I've experimented with regular downshifting before both corners. If I downshift gently after engine braking to a low speed there is no problem but it entails going around these corners very slowly! At slightly higher speeds I have experienced slight lockups on both corners. Now that I can blip when necessary I feel armed with much better skills to deal with these situations.
I’ve been doing a lot of talking with people on various forums about downshifting now and I really think that rev matching is one of those things that is a little misunderstood and perhaps even a bit overrated.
After over a decade of deliberate experimentation with different downshifting techniques on the track (including clutchless downshifting) I’m of the VERY firm belief that the true purpose of rev-matching is NOT to smooth out the shift, but simply reduce the amount of time spent to complete the shift.
Even with years of practice, a strong throttle blip will almost always impact ones braking input, something I think we can all relate to. Well, if you’re struggling with smooth braking while rev-matching (as I have for many years), ask yourself WHY you’re even blipping the throttle in the first place. If you’re using the blip as the primary means of achieving a smooth downshift, don’t. That’s what the clutch is there for. INSTEAD concentrate on how you’re using the clutch…
For me, the keys to smooth, seamless downshifts are this… EARLY downshifting (right at the very beginning if my braking zone if possible, a LITTLE blip right as I start braking impacts my braking input much less) coupled that with not fully disengaging the clutch AND (most importantly) more time spent in the friction zone to smooth it out. I found this approach gets the job done quickly, smoothly and has MUCH less of an impact on my braking inputs as I’m nearing the corner.
I never throttle blip here’s why I’m never really riding fast or hard. I have a 2007 Gsxr 1000. I simply engine brake. I would love to master the skill of Throttle bliping but it’s confusing to me. can someone explain step by step your help would be greatly appreciated.
The steps are outlined in the article, no?
I Rev Match, but I also find it very difficult to do it while getting on the front brake. I honestly don’t really need to blip the throttle on my 2014 ZX-6R for a few reasons:
1: Slipper Clutch
2: It’s a 636cc motor and as with all 600 supersports, the gear box is a close ratio box. The RPM’s between gears change very little compared to a liter bike.
3: On the street, you aren’t pushing your bike to that level.
Now I still do it, just to keep me in the rhythm of doing it on the track.
I don’t blip when riding normally (city and/or heavy traffic), but always do so when more aggressive riding is allowed. Comes from sports-car days and has simply carried over. Actually puts less stress on the machine as a result of smoother shifts. In time on one machine, it’s possible to downshift without feeling it, even when simultaneously braking. Your tranny will love you!
I blip juz to synchronize the stuff for smooth shifting not for rev matching. It’s become habit, do it without thinking.
I always blip the throttle on my singles, it helps a lot when riding a super moto to keep engine braking in check as well as prevent unnecessary sliding on the track. I started doing it when I started riding and never knew anything different. It was just another skill I carried over from performance driving.
How much do you blip? 400rpm? 500? 600? How can you tell?? One day I noticed that when I up shifted the rpm dropped 500 rpm with the bike at the same speed. Same with the next gear.. Hummm So on a down shift I blipped 500 rpm and Voila!! smooth. This along with preloading the shifter and it’s almost like an automatic tranny.. Practice this in a empty parking lot.. as you will be looking at the tach. After a while you can feel and hear the right rpm to blip at. YMMV, works for me!!
Great book btw…
Terrific, Mitch. It is a great technique when done well.
I love to blip, would rather get it all done in 1/2 second than spend a lot longer easing out the clutch. It was a challenge to learn, but such a pleasure to do well once it “clicked”.